Pneumatic Brake Fluid Bleeder Tool with 4 Master Cylinder Adapters / 90-120 psi

$26.82 Buy It Now 5d 19h, 30-Day Returns, eBay Money Back Guarantee

Seller: Top-Rated Seller yaemart-autotools (10,338) 99.8%, Location: Hebron, Kentucky, Ships to: US, Item: 131816115229 8milelake Pneumatic Brake Fluid Bleeder Tool with 4 Master Cylinder Adapters 90-120 PSIProduct DescriptionPneumatic Brake Fluid Bleeder Tool Pneumatic Brake Fluid Bleeder w/ 4 master cylinder adapters 90 -20 PSI Brake fluid bleeder works with your air compressor to quickly assist in your brake bleeding. The simplicity of this tool allows brake bleeding to get done by one person easily. Flush and refill the entire brake system by yourself with this brake fluid bleeder. Convenient one-person operation Flush and refill entire brake system 34 oz Waster Brake Fluid Tank 24 oz New Fluid tank that inserts into your master cylinder with provided adapters Master Cylinder Reservoir Adapters : 1.25 INCHES.-1.60 INCHES (32 to 41mm) 1.10 INCHES.-1.45 INCHES (28 to 37mm) 0.95 INCHES.-1.25 INCHES (24 to 32mm) 0.80 INCHES.-1.20 INCHES (21 to 30mm) Air requirement: 90 to 120 PSI, Air inlet: 1/4- 18 NPT Instructions:1. Brake bleeding procedure Refer to the vehicle manufacturer’s instructions for brake bleeding and wheel sequence before proceeding. If no specific instructions from the vehicle exist ,follow the instructions detailed below.WARNING! Familiarise yourself with the hazards of brake fluid -read manufacturers instructions on the container. Do not touch the vehicle’s brake pedal whilst bleeding the brakes.1.1 Remove the cap of the vehicle’s brake fluid reservoir. If the fluid level is not at maximum top it up.1.2 Remove the cap assembly(see fig.1-A) from the replenishment bottle and invert it within the neck of the reservoir as shown in fig.1. The threaded outlet ‘B’ must be immersed in the brake fluid. If it is not,rotate the three legged moulding ‘C’ clockwise towards the valve ‘D’ until sufficient thread is exposed to allow the outlet to be immersed in the brake fluid.1.3 Ensure the valve is closed as shown in fig.1-D.1.4 Fill the replenishment bottle just under half full with new brake fluid and screw the cap assembly back down onto the bottle. Invert the bottle over your container of new brake fluid and open the valve so that the fluid level begins to drop towards the level marked on the bottle. As soon as the level mark is reached close the valve.1.5 Place the bottle into the neck of the vehicle brake fluid reservoir as shown in fig.1, and open the valve. As the brakes are bled the fluid level in the reservoir will begin to drop and expose the bottle outlet. Brake fluid will begin to flow from the replenishment bottle. Once the level in the reservoir has risen sufficiently to cover the outlet the flow will automatically stop.1.6 Connect the brake bleeder to a suitable compressed air unit.1.7 Mount the black rubber pipe onto the brake nipple on the first wheel and open the nipple about 1/4 of a turn.(see fig.2) 1.8 Activate the brake bleeder’s trigger. The vacuum created will draw the brake fluid from the vehicle’s brake system.1.9 Continue to bleed the system until there are no air bubbles visible in the clear tube. (See fig.3)1.10 Close the brake nipple(see fig.2)1.11 Remove the rubber pipe from the brake nipple.1.12 Depress the trigger to clear brake fluid from the clear pipe.1.13 Repeat the process at each wheel in turn. 2.Changing the brake fluid2.1 Repeat the brake bleeding procedure as described above. As the fluid is being completely changed regularly, check the level in the replenishment bottle.2.2 When new fluid can be seen in the clear tube tighten the brake nipple.2.3 Repeat this procedure at every wheel.When brake bleeding and/or fluid changing is complete,test actioon of brake pedal to ensure that the brakes are working before driving the vehicle.2.4 Apply copper grease to the brake bleeding nipples before and after the brake bleeding procedure to eliminate the possibility of seized or broken nipples when the brakes are next bled(see fig.4)Features:Pneumatic Brake Fluid Bleeder Tool with 4 Master Cylinder Adapters 90 - 120 PSIFlush the entire brake system by yourself with this brake fluid bleeder.Use only DOT certified brake fluidAdapter Sizes: 21 To 30mm, 24 To 32mm, 28 To 37mm, 32 To 41mmHose Length 1-1/12 ft.Quality ProductsHave peace of mind knowing that your order will arrive original factory sealed packaging. That means that youll have the full force of the manufacturers warranty to protect your purchase.Fast and Free ShippingYoure already purchasing the item. Why pay additional for shipping, especially slow shipping? We get your order shipped out and delivered to your doorstep as quickly as possible.CommitmentWe are committed to making sure that you leave this transaction satisfied. That means having access to real people that get your questions and concerns answered quickly. Give us a shot and we will make sure that you will look to us again! Condition: New, Brand: 8milelake, Country/Region of Manufacture: China, Manufacturer Part Number: D0197, MPN: D0197

PicClick Insights PicClick Exclusive
  •  Popularity - 2,238 views, 2.1 views per day, 1,045 days on eBay. Super high amount of views. 72 sold, 14 available.
  •  Price -
  •  Seller - 10,338+ items sold. 0.2% negative feedback. Top-Rated Seller! Ships on time with tracking, 0 problems with past sales.
Similar Items